Herb 180 Trail – 2013
buy factory direct € 3.399*
Looking for a fully geared 2×10 long travel Enduro that can also handle Freeride and Bike park action with ease? Then the HERB 180 TRAIL is your perfect companion. The 180 mm travel version provides a slightly more linear characteristic which leads to a greater usage of the available travel, but ramps up smoothly towards the end of stroke to avoid bottoming out.
A great geometry and a stiff frame are the other ingredients that will create a smile on your face. The bike is built around the original aftermarket frame, whose features are described here in full detail.
Componentry wise we use the Rock Shox Monarch Plus RC3 HV shock in combination with it´s perfect match the Rock Shox Lyrik RC2DH. The drive train features a 2×10 set up with SRAM X9 Type2 roller bearing clutch rear derailleur and chain device for a silent ride. The wheels are hand build in our work shop in Germany using DT Swiss Super Competition spokes with alloy nipples. The Supra30 rims are wide, welded, have stainless steel eyelets and a very competive weight (470 g). The wheels roll on SRAM´s X9 sealed cartige bearing hubs with 20×110 mm front and 12×142 mm rear spacing. Brakes are AVID´s CodeR 4 piston type with 200 mm rotor up front and 180 mm rear.
For those who prefer a little less travel, we suggest to order this bike with the 160 mm rocker and 160 mm fork options. The HERB 180 can be converted into a HERB 160 by simply changing the rockers. If you prefer a build that is a bit lighter combined with less travel, then you should consider the HERB 160 TRAIL which features X9 2 piston brakes. The HERB 160 TRAIL is also available with the long travel options – providing you a build kit with lighter brakes combined with the longer 180 mm travel frame.
We offer the following choice options (eventual up charges are shown during the ordering process):
Tires: choose between offerings from Continental and Schwalbe
Wheel set: upgrade your wheel set with Notubes ZTR FlowEX rims
Seat post: upgrade a Rock Shox Reverb Stealth seat post
Offset bushing: it slackens the head angle and lowers the bottom bracket
Derailleur: X9 Type2 (standard) or X0 Type 2
Active Suspension Design
Linkage operated shock combined with a single pivot rear triangle. The linkage designs generates a linear beginning and mid stroke kinematics with progressive end of stroke ratio. This suspension characteristic is the optimum for excellent performance when not only suspension performance but also feedback from the bike counts. This characteristics gives you a better feeling for the bike and the ground, allowing to push through wobbles and to jump easily. We think the main suspension characteristics should be a result of the kinematics and not of the shock. Especially the air shock allows you to adjust the progression of the suspension system, but it can not be designed as freely as the kinematics of a linkage can. That´s why we believe kinematics should do the main job of defining suspension progression and the shock should be used to do the individual fine tune. Another important point is the pivot placement. Pivot palcement mainly affects two things, wheel path and climbing efficiency. Most hits on the rear wheel come from the bottom and from the front. Therefore it is desireable to have an upwards and rearwards wheel path. Generally this is difficult to achieve with any type of suspension design. Old school high pivot realize this quite well, but they are no option because of the pedal force inducing movements of the suspension. Our single pivot design, i. e. no additional pivot between the main pivot and the rear axle, provides a better wheel path than most other designs. The pivot placement – relatively high and before the bottom bracket – is crucial for that. This design results in a little extra weight, but increases the suspension performance noticeably. The exact placement of the main pivot is crucial for the climbing efficiency. We claim to have optimized that pretty well, but it´s on yourself to test the uphill efficiency. Finally we believe that any additional pivot between the rear axle and the main pivot would reduce the stiffness of the frame and thus reduce it´s overall performance.
160/180 Conversion Kit
This frame allows you to switch the rockers between the 180 mm and 160 mm travel version. Effectively this changes converts your HERB 180 to a HERB 160 and vice versa, because the frame platform for rear and front triangle is identic. When changing the rocker not only the travel is changed, but also the geometry is adjusted appropriately and the suspension characteristics are changed a bit. The longer stroke version stays a bit more linear in the mid stroke, allowing the frame to deal better with medium hard impacts. At the end of stroke both systems get progressive but to a different degree. The 180 mm version is conceptioned more as a Freeride bike, while the 160 mm version is Enduro friendly. This means the 160 offers a maximum of suspension efficiency and feedback by using its limited travel in the best way. The 180 is optimized to handle really rough terrain providing DH bike alike performance in a package that can be pedaled up the hill easily.
On this frame you can install three different rear axle Systems, all through axle systems. The standard version is 142×12 mm (compatible with X-12 standard wheels), the options are 150×12 mm through axlead 135×12 mm through axle,. To switch between the systems simply change the derailleur eye and the disc plate. 150 mm rear wheels will give the bike additional stiffness by reducing the flex of the spokes.
7000 series custom butted aluminum
The frame is designed without gussets because we use our very specially butted tube set. This design provides a clean look and supports the frame in highly stressed regions. Wall thickness on the rear triangle is specific for left and right side to handle brake and chain pull forces.
The surface of the welded and heat threated frame is ball burnished with balls of a specific size in order that the surface of the frame material is compressed. This compression leads to compression stress in the material. The compression stress changes the load factor Kappa, which leads to longer life of the frame structure.
Full complement bearings are used on all pivots. The additional balls provide a higher load capacity (C0 and Cdyn). The higher load capacity leads to greater stiffness and durability. To protect the bearings against corrosion, we decided to use stainless steel material. All bearings are cartridge type industrial grade bearings with two seals. Whenever possible the bearings are protected by the bolt heads and additional o-rings.
|Model||HERB 180 TRAIL (2013)|
|frame||HERB 180 (V1.1)|
|sizes||small, medium, large|
|shock||Rock Shox Monarch Plus RC3 HV, 216 x 63 mm|
|optional shock||Rock Shox Vivid Air R2C (2014), 216x63 mm|
|fork||Rock Shox Lyrik RC2 Mission Control DH, Solo Air, 170 mm|
|head set||Acros AiSXE-22, stainless steel bearings, red|
|stem||Truvativ AKA, 60 mm|
|optional stem||Kore Repute, 35 / 50 mm, black|
|handle bar||OCD, 800 mm wide, 20 mm rise, black|
|optional handle bar||Kore Mega, 760 mm wide, 20 mm rise, blackKore|
|grips||Kore Rivera, lock on, closed aluminium cap|
|brakes||Avid Elixir 9 Trail, 200 mm front rotor, 180 mm rear rotor|
|derailleur||Sram X9 Type 2, short cage|
|optional derailleur||Sram X0 Type 2, short cage|
|front derailleur||Shimano XT FDM-970-10|
|shifters||Sram X9 Trigger|
|cassette||Sram PC-1070, 10 speed, 11-32 T|
|crank and bottom bracket||SRAM S1400, hollow forged, 22T, 36T, bash guard|
|chain device||NC-17 Stinger|
|rims||Alexrims SUPRA30, welded, 32 hole, black|
|optional rims||ZTR FlowEX, welded, 32 hole, black|
|spokes and nipples||Sapim Race, 2,0 x 1,8 x 2,0, aluminum nipples|
|hubs||SRAM X9, front 20/110 mm, rear 12/142 mm, black|
|tires||Schwalbe Hans Dampf, 2,35“, Trailstar Compound|
|optional tires||Continental Mountain King II, 2,4“, foldable|
|seat post||Kore, Twin Bolt, 31,6 x 350 mm, black|
|optional seat post||Rock Shox Reverb Stealth, 150 mm adjustabe, 31,6 x 430 mm|
|seat||Selle Italia SLS Kit Carbonio|
|seat clamp||Syntace Super Lock 2|
|example fork||Rock Shox Lyrik 2013||Rock Shox Lyrik 2013||Rock Shox Lyrik 2013|
|fork travel||170 mm||170 mm||170 mm|
|fork length + head set height||555 + 2 mm||555 + 2 mm||555 + 2 mm|
|top tube (reach)||383 mm||416 mm||449 mm|
|top tube sloped||505 mm||536 mm||567 mm|
|top tube horizontal||569 mm||601 mm||637 mm|
|chain stay length||426 mm||426 mm||426 mm|
|seat angle (actual)||69,8°||69,8°||69,8°|
|seat angle (effective||73,3°||73,3°||73,3°|
|head tube length||130 mm||130 mm||140 mm|
|wheel base (40 mm fork offset)||1126 mm||1159 mm||1192 mm|
|seat tube length||428 mm||428 mm||490 mm|
|bottom bracket height||15 mm||15 mm||15 mm|
|bottom bracket can be lowered with offset spacers|
* The indicatet price may vary for different product versions, value added tax included , visit last-bikes-shop.com for details and terms and conditions.